7mm Remington Ultra Magnum Reloading Essentials

This two-die set is intended for reloading bottleneck cases, and consists of a Full-Length Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions. It sizes the outside of the case, de-primes and expands the neck to accept the bullet. The die has vents to prevent case damage caused by trapped air and for excessive lubricant. Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing. The included Seater Die has a built-in roll crimper to secure the bullet at the same time as it’s seated.

Don't forget the shell holder - Click Here to Get Yours.

• Standard 7/8"-14 Thread
• Proprietary Die Steel
• Set includes Full-Length Sizing die and Bullet Seating Die
• Sizing die brings cases to SAAMI minimum cartridge dimensions
• Ships in Green Die Box

RCBS Single Stage shell holders are built from hardened steel and designed to properly align the case with the reloading die in single-stage and turret presses. They’re sized to fit specific case heads and capture 0.125 inch of the case head for proper SAAMI headspacing.

• 348 Winchester
• RCBS shell holders are built for Single Stage and Turrets Presses.
• RCBS shell holders are manufactured to exacting tolerances.
• RCBS shell holders are hardened for years of use.
• RCBS shell holders ensure proper alignment between the cartridge and die.
• The Shell holders are cut to .125" depth for proper headspacing.
• RCBS Limited Lifetime Warranty.

RCBS Single Stage shell holders are built from hardened steel and designed to properly align the case with the reloading die in single-stage and turret presses. They’re sized to fit specific case heads and capture 0.125 inch of the case head for proper SAAMI headspacing.

• 26 Nosler
• 300 PRC
• 300 Remington Ultra Magnum
• 28 Nosler
• 7mm Remington Short Action Ultra Magnum
• 7mm Remington Ultra Magnum
• 300 Remington Short Action Ultra Magnum
• 338 Remington Ultra Magnum
• 375 Remington Ultra Magnum
• 455 Webley
• 6.5 PRC
• RCBS shell holders are built for Single Stage and Turrets Presses.
• RCBS shell holders are manufactured to exacting tolerances.
• RCBS shell holders are hardened for years of use.
• RCBS shell holders ensure proper alignment between the cartridge and die.
• The Shell holders are cut to .125" depth for proper headspacing.
• RCBS Limited Lifetime Warranty.

RCBS Single Stage shell holders are built from hardened steel and designed to properly align the case with the reloading die in single-stage and turret presses. They’re sized to fit specific case heads and capture 0.125 inch of the case head for proper SAAMI headspacing.

• 300 Winchester Magnum **
• 7mm Remington Magnum
• 257 Weatherby Magnum
• 264 Winchester Magnum **
• 6.5 Remington Magnum
• 270 Weatherby Magnum
• 7mm Shooting Times Westerner
• 7mm Weatherby Magnum
• 300 RCM
• 30-338 Winchester Magnum
• 300 Holland & Holland Magnum
• 300 Weatherby Magnum
• 308 Norma Magnum
• 8mm Remington Magnum
• 338 RCM
• 338 Winchester Magnum
• 340 Weatherby Magnum
• 350 Remington Magnum
• 9.3mm x 74 Rimmed
• 375 Ruger
• 375 Holland & Holland Magnum
• 416 Ruger
• 416 Remington Magnum
• 450 Marlin
• 458 Winchester Magnum
• 458 Lott
• 460 Smith & Wesson
• RCBS shell holders are built for Single Stage and Turrets Presses.
• RCBS shell holders are manufactured to exacting tolerances.
• RCBS shell holders are hardened for years of use.
• RCBS shell holders ensure proper alignment between the cartridge and die.
• The Shell holders are cut to .125" depth for proper headspacing.
• RCBS Limited Lifetime Warranty.

These high-quality replacement parts are compatible with the RCBS® Rock Chucker®, Reloader Special™ and most C-frame single-stage presses.

RCBS® Case Trimmer Collets work like a draw collet on a lathe. They secure cases for trimming to length. Note: For use with Rotary Case Trimmer and Rotary Case Trimmer—2 only.

RCBS® Case Trimmer Pilots are tapered to guide pilot into the case mouth. The design prevents a case from wobbling when being trimmed to length. For use with RCBS® Trim Pro® Case Trimmers, Rotary Case Trimmer—2 and Rotary Case Trimmer. For use with RCBS Case Trimmers only.